Understanding Stair Stringer Basics and Why Calculations Matter
A stair stringer is the diagonal structural support that holds up your steps. It's essentially the backbone of any staircase, whether you're building indoor stairs, outdoor deck stairs, or basement stairs. The stringer has notches cut into it where the treads (horizontal steps) and risers (vertical pieces between steps) sit. Most staircases use two stringers—one on each side—though larger staircases might have a center stringer for additional support.
Free Guide to Getting On a Game Show →
Calculating stringers correctly is critical because improper measurements lead to stairs that don't fit the space, are uncomfortable to use, or worse, become safety hazards. Building codes in most jurisdictions specify that residential stairs must have a rise (vertical height of each step) between 7 and 7.75 inches and a run (horizontal depth of each step) between 10 and 11 inches. These measurements exist because they match how people naturally climb stairs. Steps that deviate significantly from these standards cause people to trip or stumble.
The calculation process involves several key measurements: the total rise (floor-to-floor height), the total run (horizontal distance covered by all steps), the individual rise per step, the individual run per step, and the number of steps needed. Understanding what each measurement represents helps prevent costly mistakes. Many DIYers and even some professionals make errors by confusing total measurements with individual step measurements, which can result in stringers that don't work for the space.
Practical takeaway: Before ordering materials or cutting any stringers, measure your total rise and total run multiple times using a level and tape measure. Small measurement errors compound when you're calculating multiple steps, so accuracy at this stage saves time and materials later.
Measuring Total Rise and Total Run Accurately
Total rise refers to the vertical distance from the finished floor level at the bottom to the finished floor level at the top. This is not simply measuring from one concrete floor to another—you must account for finished floor materials. If your lower level has 3/4-inch hardwood flooring and your upper level has 1/2-inch tile, these differences matter. The total rise is measured from the top surface of the lower flooring to the top surface of the upper flooring.
Get Your Free Dental Implant Cost Guide Albany Georgia →
To measure total rise, use a long level and a tape measure. Place the level horizontally from your lower floor to the upper area, keeping it perfectly level using the bubble indicator. Then measure the vertical distance from your level down to the lower finished floor. Add this to the vertical distance from your level up to the upper finished floor. Alternatively, use a laser level or transit level if you have access to one—these tools provide more accuracy across longer distances. Most building codes require measuring to 1/16-inch precision, though 1/8-inch accuracy is acceptable for residential work.
Total run is the horizontal distance your staircase will cover from start to finish. This is simply the sum of all individual step runs added together. For example, if you're building 14 steps with 10-inch runs each, your total run would be 140 inches or about 11 feet 8 inches. This measurement determines where your staircase will land at the top and whether it fits in your available space. Many builders use a plumb bob and measuring tape to establish this distance on the floor, marking where the bottom of the stringer will sit and where the top will land.
Practical takeaway: Create a simple diagram showing your measurements. Draw a vertical line for total rise and a horizontal line for total run, then note the exact figures. This visual reference prevents confusion during the calculation phase and gives you something to verify against before you cut anything.
Calculating the Number of Steps and Individual Rise
Once you know your total rise, calculating the number of steps and individual rise involves straightforward division. You'll divide your total rise by the target individual rise—typically 7 to 7.75 inches for residential stairs. Let's work through an example: if your total rise is 105 inches, and you want an individual rise of 7 inches, you would divide 105 by 7 to get exactly 15 steps. However, staircases rarely work out this perfectly.
Learn About Ohio Vehicle Registration Information →
More commonly, you'll get a decimal number. If your total rise is 107 inches divided by 7.5 inches, you get 14.27 steps. Since you can't have a partial step, you need to round and recalculate. With 14 steps, your individual rise would be 107 ÷ 14 = 7.64 inches per step (within code). With 15 steps, your individual rise would be 107 ÷ 15 = 7.13 inches per step (also within code). Both options work, but the one with 15 steps creates slightly smaller rises, which some people find easier to climb.
The key principle here is that all rises in a single staircase must be equal or within 3/8-inch of each other according to most building codes. You cannot have one step that's 7 inches and another that's 8 inches—this creates a tripping hazard. Once you've determined the number of steps, divide your total rise by that number to establish your exact individual rise. Round to two decimal places for your calculations. This process ensures that every step in your staircase will be consistent and code-compliant.
Practical takeaway: Try your division both ways (rounding up and down in step count) and compare both individual rise measurements to building code requirements. Choose the option that gives you rises closest to the standard 7 to 7.75 inches, as this creates the most comfortable staircase for regular use.
Determining Individual Run and Accounting for Nosing
Individual run is the horizontal depth of each step, measured from the back of one step to the back of the next step. This is not the same as the tread depth—the nosing (the edge of the tread that overhangs the riser below) must be accounted for separately. Building codes typically require a minimum run of 10 inches and a maximum run of 11 inches for residential stairs, measured from nosing edge to nosing edge. Nosing itself typically extends 1 to 1.5 inches beyond the riser.
Your Free Guide to Aloha Q Appointments →
To determine your individual run, divide your total run by the number of steps. Using our earlier example: if your total run is 140 inches and you have 14 steps, your individual run would be 140 ÷ 14 = 10 inches. This works within code requirements. However, you should also account for how the stringer gets cut. When you notch a stringer, you create a triangle-shaped cutout for each step. The run of each notch represents where the tread will sit, but you need to think about the nosing overhang as well.
When calculating stringer cuts, many builders use the full tread depth plus nosing for the run measurement. If you're using 11-inch-deep treads with 1.25-inch nosing, your run measurement for the stringer might be 12.25 inches, depending on how you prefer to construct the stairs. The specific measurement becomes important when you're laying out the notches on your stringer material. Some builders subtract the nosing from their calculation, while others include it. Consistency in your approach matters more than which method you choose, as long as the final stairs meet code requirements.
Practical takeaway: Measure an existing commercial staircase if possible—check the rise and run of several steps to see actual measurements in practice. This gives you a feel for what different rise and run combinations feel like to climb, helping you make informed decisions if you have options between a few different calculations.
Creating a Stringer Layout and Cutting Diagram
Once you've calculated your rise and run, creating a physical layout on your stringer material is the next step. Most residential stringers use 2x12 lumber, which provides adequate depth for notching. Your layout involves marking each notch's location, accounting for the fact that the first step might be different from the rest if your staircase has a landing or if it starts at a certain height.
How to Pay Your Coweta Fayette EMC Bill Online →
To create a cutting diagram, you'll need a framing square—a tool with a long body and shorter tongue that forms a right angle. The framing square becomes your guide for marking consistent step notches. You set the body of the square to your run measurement (say, 10 inches) and the tongue to your rise measurement (say, 7.5 inches). Then